Sept 16th...this is it....The LAST one

[Sheppo]

I'll be there either on my bike or in the cage. I finally repaired the damage on my bike. Sheppo those parts you gave me worked perfectly! Let me know what you want for $ for them. I also installed some clip on handle bars, but I had to move the head light assembly down to fit the clamps on. Now the front end is going to bottom out really bad! Sheppo do you think a suspension adjustment would fix that?

Merry Christmas on the parts


what's bottoming out, the fender on the head light? or?? I can't imagine your forks bottoming out. Sounds like the headlight might need custom mounts with the clip ons..

[BCT748]

Anyone going from Seacoast in Derry this time? I've been trying to make it to one all year with no luck.

[SoxPrincess83]

Thanks Sheppo! I still owe you a beer though, so you'd better be up for Lin Garden Tuesday!!!

It's the head light mount smacking into where the forks go into the wheel. I had to drop the head light mount down in order to fit the clamps onto the forks, I had to take it down by about an inch. I'll have to look around to see if I can find any custom head lamp mounts... *swears*

[Sheppo]

Thanks Sheppo! I still owe you a beer though, so you'd better be up for Lin Garden Tuesday!!!

It's the head light mount smacking into where the forks go into the wheel. I had to drop the head light mount down in order to fit the clamps onto the forks, I had to take it down by about an inch. I'll have to look around to see if I can find any custom head lamp mounts... *swears*

OK so the headlight hits the fender or some part because it's lower.. hmmm can you trim the top part of the original bracket to push it up a bit higher? *goes off to look at the 'puter*

I'll be at the garden

[ThisBitch]

Just so we don't miss anyone this week... Why don't we have everyone meet at the NESR banner near the flagpole at 8. We'll make introductions, shoot the shit and then head out for Chinese.

I'll bring nametags

[Wrynne]

what time are you available to leave? I am leaving BMS and not sure if I'll leave at 4:45ish to ride to the Dew in Wakefield to ride with the others OR leave BMS at 6ish and go straight there. Let me know.

Doug

I'm out of work by 4/430 and I drive by BMS on my way home...(which is literally 5 min from BMS) I'd be up for either option.

[Sheppo]

Thanks Sheppo! I still owe you a beer though, so you'd better be up for Lin Garden Tuesday!!!

It's the head light mount smacking into where the forks go into the wheel. I had to drop the head light mount down in order to fit the clamps onto the forks, I had to take it down by about an inch. I'll have to look around to see if I can find any custom head lamp mounts... *swears*

OK so you need to modify the headlight brackets that mount to the fork tubes to raise the light the amount you had to lower it to accomidate the clipons. can it be cut and welded? Bent? cut and welded to the clipon? I would imagine the light sucks now being an inch +/- lower.

[Sheppo]

I'm out of work by 4/430 and I drive by BMS on my way home...(which is literally 5 min from BMS) I'd be up for either option.

cool lets touch base Monday/Tuesday

[SVRACER01]

I could probably meet up with some people in NH and ride down.

I still don't think I will have a job by next week, so I will basically be riding all day before going to bike night.

I think one of the previous posters indicated he might be heading down from Maine. I might try to meet up with him and then pick up people in NH.

that was me, im Ports, so i assume that you have to pass by there on your way down unless you take some wacky route.

[SoxPrincess83]

OK so you need to modify the headlight brackets that mount to the fork tubes to raise the light the amount you had to lower it to accomidate the clipons. can it be cut and welded? Bent? cut and welded to the clipon? I would imagine the light sucks now being an inch +/- lower.

Right. I don’t know how to weld and I don’t think my Dad has the tools either. I may have to search for a prefabricated option I think. I’m not sure how well my headlights work, I haven’t ridden the bike since I switched the parts. I’ve gotten complaints about my headlights on low beam before though, so hopefully its not too bad.

[KillBill]

Anyone going from Seacoast in Derry this time? I've been trying to make it to one all year with no luck.

What time are you out of work?

[Sheppo]

Right. I don’t know how to weld and I don’t think my Dad has the tools either. I may have to search for a prefabricated option I think. I’m not sure how well my headlights work, I haven’t ridden the bike since I switched the parts. I’ve gotten complaints about my headlights on low beam before though, so hopefully its not too bad.

Let me see what I can come up with Stay tuned...

[BCT748]

What time are you out of work?

I'm usually out of work at 2:30, when I get home depends on where I am working that day. I could be working in Lowell, Lawrence, Bradford or Newton. If I'm in Newton I would get home around 4-430, anywhere else would be 3-330.

you and that coyote

[Brian675]

What time are you out of work?

[BCT748]

you too, fucking wanna be euro trash hole

[KillBill]

So you bitches going to bike night or what

[ff36buell]

Have fun guys, gotta work...

[Woodsy]

Have fun guys, gotta work...

TJ,

since nick is out do you want to lead? this has 2 advantages 1. you know where you are going and 2. since you will already be in front you wont have to pass me on the outside. although nick way nice enough to unload some corsa III's on me and i changed my gearing so maybe that will help things.

[BCT748]

So you bitches going to bike night or what

[Wanderer]

I'll try to make it out for this one

[johnnym]

any south of boston riding up?

if not ill ride to the dew and meet everyone else

[schleppy]

I'll go if the weather is nice.

[KillBill]

I'm usually out of work at 2:30, when I get home depends on where I am working that day. I could be working in Lowell, Lawrence, Bradford or Newton. If I'm in Newton I would get home around 4-430, anywhere else would be 3-330.

you and that coyote

If you want to meet up in the Wilmington area with Pigman and I
you're more than welcome.

[ThisBitch]

tomorrow, i dont exactly know where I will be riding to lowell from........

my plan for the day is to do riding around in the MA area; so maybe worcester, N. MA area, etc.

Maybe surprise visit a few of my class of 08 friends at work!!

so yeah, sry to any1 who was looking to hitch a ride down from Maine or Portsmouth - it is still def ok for u to ride down solo

I just want to hang around MA more because I havent done much of it

[CEO]

so yeah, sry to any1 who was looking to hitch a ride down from Maine or Portsmouth - it is still def ok for u to ride down solo

Well, I am sure they appreciate having your permission to attend an open public event and get there in/on the transportation mode of their choosing. What a nice guy!