0
![Not allowed!](http://www.nestreetriders.com/forum/images/buttons/down_dis.png)
![Not allowed!](http://www.nestreetriders.com/forum/images/buttons/up_dis.png)
Hey Guys,
Does anyone have a link to a comprehensive guide (or video) on moving a bike safely in the bed of a pickup? I may or may not have to transport my new bike home in this manner depending on how the weather is and how sandy the roads stay in the next 2 weeks so I would like to make sure that I have a solid knowledge of this as well as any materials that I might need before I try to move a $7500 piece of machinery and see it tumbling down the street in my rearview mirror 10 minutes later![]()
2008 Ebony Special Edition ZX-6R
1995 ZX-6 Red (SOLD)
two ratchet straps and a ramp. Roll it or drive it up, put the ratchet straps to the tie downs in the pick up and attach them to the bike. Most likely you'll need straps that wrap around your triple trees to attach too. Then tighten the rachet straps down until the bike is solid. I also recommend straps in the back to keep the back square so it doesnt move side to side over bumps. Some might think that's over kill.
As for loading, if you can find a bit of a hill it makes getting it INTO the truck a lot easier. At my house I'll actually back my truck up to the curb, so it gives me another 6inches-1foot of height. Takes a lot of the angle out of the ramp.
Getting it on the truck shouldn't be a big deal. I'm picking it up at Nault's Honda/Kawi in Windham and will have basically everyone at the shop to help me. My main concern is having it tied down properly.
Of course I'm banking on just riding the damn thing home. I just don't want to risk anything if the roads are still bad. Spring needs to hurry the f*** up and get here!
2008 Ebony Special Edition ZX-6R
1995 ZX-6 Red (SOLD)
Its really not that complicated, but I was nervous the first time I did it as well....its the type of thing that you really want to see once or twice.
I recommend taking someone with you who has experience loading a bike. There are some dealers that will explicitly not help load a bike into a personal truck for fear of dropping it, so check with the dealer before you go there assuming you will have help.
Is it your truck? Will you be moving the bike in the bed on a regular basis for track days etc? If so, it is worthwhile to buy what you need rather than borrow. Nothing helps more than long wide ramps, a condor wheel chock, a cycle cynch some soft ties and 4 high quality ratchet straps. Do some searches on google, i remember finding some good stuff when I went through this a few years ago.
EVERYTHING is a repost
06 749R #0047
08 R 1200 GSA
13 Monster EVO 1100
look into to go through the bars the strap attaches to wanna say their called canyon dancers
http://www.kneedraggers.com/details/...I--625318.html
Last edited by crowspeed07; 02-23-09 at 05:17 PM.
ya i have a canyon dancer harness, theyre great for my zx9 but horrible for my buddies r6, all depends on where your bars are in relation to your fairings, but you can always go to the triple.
"Chatbox...It's like Vegas, for your fingers."
Originally Posted by CBR_Knight
in my own thread, let me post this:
first of all, nothing about sex or play with a female seems interesting or arousing to me....
"BALLS" is coming home late after a night out with the guys smelling of perfume and beer, lipstick on your collar, slapping your wife on the ass and having the balls to say "you're next!"
If you do not have a wheel chock I would deflate the front tire. Not all the way to the rim! This gives you a flatter/wider contact for the front wheel on and into the truck bed. Less ap to turn on you. Careful with canyon dancers. They tend to pull on the grips binding the throttle grip and possible stretching the cables.
Gino
HAWK GT Racer Expert #929
2012 CCS LRRS ULSB Champion
2012 CCS LRRS P89 Champion
2008 CCS ULSB National Champion
ECKRACING Bridgestone Street & Competition Woodcraft MOTUL On Track Media Pine Motorparts Vanson Leathers
as everyone has stated, get some ratcheting tie-downs
if you don't have any, when purchasing, just avoid the really cheap ones, because the hook may bend and break while holding the bike
motorcycle specific tie downs are nice because you can loop the hook around back onto the strap so that there's a "soft loop" wrapping around your triple clamps instead of a metal hook
if you're unsure about whether or not the bike is tied down properly, go ahead and ask at the dealership, they should be able to help you
Last edited by breakdirt916; 02-23-09 at 07:48 PM.
There's stuff to watch out for when tieing a machine down....brake lines, throttle cables, contact with fairings, etc.
I can make it really easy for you.
I have a truck and enclosed trailer and live 13 minutes from Nault's Windham.
Yeah I set-up my truck to haul my bike around when necessary, but I would also recommend you do it with someone else the first time. If you don't have a wheel chock in the bed, it's likely that the wheel will turn and the bike will tilt over and potentially fall (unless your tie downs are at identical angles so that one doesn't pull slightly more than the other).
For picking the bike up let someone help you and for track days and other occasions you can take your time getting ramps, proper tie downs, and a wheel chock for the bed.
I bought a cheap wheel chock on e-bay and bolted it into the bed, and I have one folding ramp with walls to keep the tires from falling off- I got it on craigslist, and I got a second ramp for me to walk up on that is one of those ReadyRamps- that doubles as a bed extender. Got that one on e-bay as well. And I just use ratcheting tie-downs that I bought at home depot to hold the bike down.
Current:
00 Aprilia RSV-R
Past:
06 R6
05 R6
97 Honda F3
Make life easy for yourself and just ride it home. You will get a clear day in the next 3 weeks for sure...have them prep it ASAP and the first nice day skip out of work and get the friggen thing.
EVERYTHING is a repost
06 749R #0047
08 R 1200 GSA
13 Monster EVO 1100
the economy really sucks these days! there are plenty of people looking to make a few bucks however they can. i just bought a 6x8 trailer for $200.00-complete with three wheel chocks. trailer will hold one or two bikes. way easier than trying to get it into the bed of the f150.
later odieoh24
I always take the time to make a small wheel holder with 2x4
Like a giant I that fits in the truck only takes minutes and a hand full of screws. Left and right cross beams hold it in the bed. parrallel length wood the wheels fit in
Glen Beck is John the Baptist
not sure if this will help much...but i had a thread about this last summer. i posted some pics of my final loading.
http://www.nestreetriders.com/forum/...to-pickup.html
it's about loading two bikes, but it's similar.
- Jamie
2009 K 1300 S
I actually picked up my last bike in NJ and put it in my truck with the front wheel turned/locked and the kickstand down, I then pulled tiedowns on front on each side of the triple clamp down tight, the side opposite of the kickstand tighter so it was not actually sitting on its side. Then lastly I pulled 2 more tiedowns on the passenger peg mounts to the rear of the truck so it was supported in all four corners, no wheel chock or anything necessary. Then I went 80 mph for 4 hours.
LRRS #399
MX #505