0


Stolen straight from ODFU for your reading pleasure
DRILL PRESS: A tall upright machine useful for suddenly
snatching flat metal bar stock out of your hands so that it
smacks you in the chest and flings your beer across the
room, splattering it against that freshly painted airplane
part you were drying.
WIRE WHEEL: Cleans paint off bolts and then throws them
somewhere under the workbench with the speed of light. Also
removes fingerprint whorls and hard-earned guitar calluses
in about the time it takes you to say, "Ouch...."
ELECTRIC HAND DRILL: Normally used for spinning pop rivets
in their holes until you die of old age.
PLIERS: Used to round off bolt heads.
HACKSAW: One of a family of cutting tools built on the
Ouija board principle. It transforms human energy into a
crooked, unpredictable motion, and the more you attempt to
influence its course, the more dismal your future becomes.
VISE-GRIPS: Used to round off bolt heads. If nothing else
is available, they can also be used to transfer intense
welding heat to the palm of your hand.
OXYACETYLENE TORCH: Used almost entirely for lighting
various flammable objects in your shop on fire. Also handy
for igniting the grease inside the wheel hub you want the
bearing race out of.
WHITWORTH SOCKETS: Once used for working on older British
cars and motorcycles, they are now used mainly for
impersonating that 9/16 or 1/2 socket you've been s
searching for the last 15 minutes.
HYDRAULIC FLOOR JACK: Used for lowering an automobile to
the ground after you have installed your new disk brake
pads, trapping the jack handle firmly under the bumper.
EIGHT-FOOT LONG DOUGLAS FIR 2X4: Used for levering an
automobile upward off a hydraulic jack handle.
TWEEZERS: A tool for removing wood splinters.
PHONE: Tool for calling your neighbors to see if he has
another hydraulic floor jack.
SNAP-ON GASKET SCRAPER: Theoretically useful as a sandwich
tool for spreading mayonnaise; used mainly for getting dog
**** off your boot.
E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder
than any known drill bit that snaps off in bolt holes you
couldn't use anyway.
TWO-TON ENGINE HOIST: A tool for testing the tensile
strength on everything you forgot to disconnect.
CRAFTSMAN 1/2 x 16-INCH SCREWDRIVER: A large prybar that
inexplicably has an accurately machined screwdriver tip on
the end opposite the handle.
AVIATION METAL SNIPS: See hacksaw.
TROUBLE LIGHT: The home mechanic's own tanning booth.
Sometimes called a drop light, it is a good source of
vitamin D, "the sunshine vitamin," which is not otherwise
found under cars at night. Health benefits aside, it's main
purpose is to consume 40-watt light bulbs at about the same
rate that 105-mm howitzer shells might be used during, say,
the first few hours of the Battle of the Bulge. More often
dark than light, its name is somewhat misleading.
PHILLIPS SCREWDRIVER: Normally used to stab the lids of
old-style paper-and-tin oil cans and splash oil on your
shirt; but can also be used, as the name implies, to strip
out Phillips screw heads.
AIR COMPRESSOR: A machine that takes energy produced in a
coal-burning power plant 200 miles away and transforms it
into compressed air that travels by hose to a Chicago
Pneumatic impact wrench that grips rusty bolts last over
tightened 58 years ago by someone at ERCO, and neatly
rounds off their heads.
PRY BAR: A tool used to crumple the metal surrounding that
clip or bracket you needed to remove in order to replace a
50¢ part.
HOSE CUTTER: A tool used to cut hoses too short.
HAMMER: Originally employed as a weapon of war, the hammer
nowadays is used as a kind of divining rod to locate the
most expensive parts not far from the object we are trying
to hit.
MECHANIC'S KNIFE: Used to open and slice through the
contents of cardboard cartons delivered to your front door;
works particularly well on contents such as seats, vinyl
records, liquids in plastic bottles, collector magazines,
refund checks, and rubber or plastic parts.
DAMMIT TOOL: Any handy tool that you grab and throw across
the garage while yelling "DAMMIT" at the top of your lungs.
It is also the next tool that you will need.
FUCK: A balm, usually applied verbally in hindsight, which
somehow eases those pains and indignities following our
every deficiency in foresight.
-Pete
NEMRR #81 - ECK Racing
Cyclesmith Track Days
Woodcraft | MTag-Pirelli | OnTrack Media
'03 Tuono | '06 SV650 | '04 CRF250X | '24 Aprilia Tuareg
Cant forget the flathead screwdriver, otherwise known as the finger stabber.
I know a little about everything, and alot about nothing.
You know what's really funny, I have all those tools and use them on a daily basis!!
I also have bottles of various oils and volatile fluids for kicking and knocking over while your hands are full.
It's all water under the bridge, and we do enter the next round-robin. Am I wrong?
I thought this was going to be a thread naming site members![]()
he forgot impact universal joints - good for getting to that hard to reach fastener you forgot to torque so youcan forget about it again after you're done chasing down the socket that just flew off the end of said joint.
Don't forget the welder.Originally posted by mmracer37
You know what's really funny, I have all those tools and use them on a daily basis!!
A tool used to make the prettiest bead ever seen by man, only to realize that the part is rotated 180 degrees.
G-man
Gerard
On my Ultimate Tool List, Pete, you're at the very top![]()
Boston --> San Diego
Socket Wrench: serves two functions at once; bloodies knuckles as it rounds frozen bolt-heads (by slipping off) causing you to punch the ground, engine, etc...
"Up front there ought to be a man in black." -John Cash
LISTEN TO SLAYER
If I get another fuckin' bike stolen...
stroboscopic light used to illuminate grease build up
Originally posted by a13x
On my Ultimate Tool List, Pete, you're at the very top![]()
![]()
I still love the smell of burnt racing fuel in the morning!