Degsy's new racebike. Ongoing project
Hey Degs....do we have to rejet???
Degsy's new racebike. Ongoing project
Nope, don't have no jets!!!
I also just received my Akrapovic full Ti race system though, so we need soon to do some tuning work.
Anyone know a dyno shop that would donate some time and expertise in exchange for stickers on the bike?
Degsy
I polished and trimmed the triple tree for my race bike.
Milled out the part that holds the ignition switch and stamped NESR on it, and slightly polished the clamp. Looks more like a factory special piece now. Bling bling.
Degsy's new racebike. Ongoing project
Degs,
I sent ya a PM ya read it yet?
Degsy's new racebike. Ongoing project
Thanks to Steve (snaggle) I have just snagged a set of world supersport HRC electrics for my racebike. Comes with HRC programmable ECU (no power commander needed), software for programming it, full HRC wiring loom (cuts out ignition switch and all lighting), HRC guages, adjustable tach and shift light etc etc etc. Woohoo!!!
Degs
Degsy's new racebike. Ongoing project
HRC..........nice degs!
i'm gonna need you to get rid of my key/ignition set-up if you can. holla back when u get a chance...
peace
Degsy's new racebike. Ongoing project
Glad you could get it. Sounds sweet!!, Does this mean we no longer have to figure out the total loss ignition?
Degsy's new racebike. Ongoing project
No, it means that we don't have to figure out how to bypass the ignition/lock unit. The kill switch on the right handlebar is now the ignition instead of the key assembly.
I decided against total loss ignition as it is too tricky and risky to use.
Here's the HRC electronics kit.
The item in the plastic bag is a new ECU. Wiring harness, Instruments, ECU with rubber mount, ECU mounting bracket and rubber strap, Ignition pulsar, kill switch, bank angle sensor, programming interface cable. This is the FIM race kit.
Degsy's new racebike. Ongoing project
and yes, you read correctly, that tach goes up to 17000 rpm!!!
Degs
Degsy's new racebike. Ongoing project
That is too cool!!!
Shift light..Heehee!!:D :D
Degsy's new racebike. Ongoing project
I am doing some major work on the bike this weekend. I will be reassembling the front end and putting the race exhaust system on as well as fitting my HRC electrics and probably starting the motor for the first time.
Any of you local peeps who want to swing by to help out and have a beer or two are welcome.
Degs
Degsy's new racebike. Ongoing project
This is a kiddie weekend for me so I'm out,
Degsy's new racebike. Ongoing project
Did some work this weekend.
Spencer (DaSpence) came over and helped me revalve the forks and put the front end back together. Couldn't install the exhaust system as it wouldn't fit with the bike on a stand so that will go on when the wheels are painted and refitted to the bike. The HRC electrics haven't arrived yet so that will have to wait also.
Degsy's new racebike. Ongoing project
Spencer working on the F4i
Degsy's new racebike. Ongoing project
Degsy's new racebike. Ongoing project
Degsy's new racebike. Ongoing project
Lookin' good Degs! Can't wait to get up there with the team. Have you received the Pit shirts yet?
Degsy's new racebike. Ongoing project
check on the NESR racing merchandise section.
degs
Degsy's new racebike. Ongoing project
Yep it was a fun weekend working on the the F4i with Derek. I learned a lot with forks and tools and vocabulary of parts. We came to a few dead ends due to "special tools" but it worked out fine. Can't wait to work on the bike again. :D
Degsy's new racebike. Ongoing project
Why am I scared about this "special tool thing" ?
Degsy's new racebike. Ongoing project
This is where I stand also... Frame swing arm and motor... Any of you RI guys going to be around this week???
G-man
Degsy's new racebike. Ongoing project
Dont worry Ed all it took was a rubber mallot and a flat head screw driver......the NESR "Special Tool".
Degsy's new racebike. Ongoing project