Project: Grom 2.0

[xrocket21]

Auto tuners work SO much better when they are plugged in....

Lol, we've all been there

[feralchimp]

Really appreciate all the progress and consistent posts, Jim. So many steps of this are beyond my personal "yeah I'd try that" limit; great to see you working through the stuff as it arises.

[Jim]

Bent the foot brake lever to clear the case cover




Sent from my iPhone using Tapatalk

[Jim]

Finally got the exhaust mounted and it’s super tight to the frame




Sent from my iPhone using Tapatalk

[Jim]

Trimmed the rear tire fender to fit with the exhaust




Sent from my iPhone using Tapatalk

[Jim]

300 swap header is 51mm OD.
LeoVince can is 53mm ID.

Weighing out options to have the header flared, clamp it, or get a can that fits better.


Sent from my iPhone using Tapatalk

[Jim]

Found someone with the tuning cable to connect the laptop to the bike, but figured out I can download the Bluetooth link app on the laptop to flash the ECU via laptop Bluetooth.

Selected the 2018 Grom stock map and we’re off…




Sent from my iPhone using Tapatalk

[Jim]

Now that the flash is completed, my mobile app is showing other bike models, like it should have been.

Now my ECU is mapped correctly.




Sent from my iPhone using Tapatalk

[Jim]

Current issue is there are still no RPMs on the dash. Will keep troubleshooting that.

The bike is essentially ridable once the front sprocket arrives.

Remaining list:
- order new muffler (tomorrow)
- install new O2 sensor (arrives Monday)
- install crankcase breather filter (arrives a week from today)
- oil the air and breather filters
- install chain
- install plastics
- trim front plastics to fit radiator
- setup dash again


Sent from my iPhone using Tapatalk

[RandyO]

300 swap header is 51mm OD.
LeoVince can is 53mm ID.

Weighing out options to have the header flared, clamp it, or get a can that fits better.


Sent from my iPhone using Tapatalk

my fabricator just welded my muffler 1.75"id to my header pipe 1.25"id . he made a short cone shaped flare for the transition

[xrocket21]

Found someone with the tuning cable to connect the laptop to the bike, but figured out I can download the Bluetooth link app on the laptop to flash the ECU via laptop Bluetooth.

Selected the 2018 Grom stock map and we’re off…




Sent from my iPhone using Tapatalk

I had a ton of problem flashing my RC8R, turns out you can see and monitor, but you can't flash over bluetooth for me!

[Jim]

I had a ton of problem flashing my RC8R, turns out you can see and monitor, but you can't flash over bluetooth for me!

the aRacer stuff is made for bluetooth tuning and config

[Jim]

spoke to one of the experts that know this stuff and he recommended using the 2016 Grom map as a base model for all 2016-20 models.

flashed the ECU again and set it up for auto tuning and fuel

[Jim]

RPM on the dash fixed with flashing the 2016 Grom.

New Hindle muffler arrives tomorrow.
New O2 sensor arrives Monday.
Crankcase breather arrives Tuesday.

No update on the front sprocket.

Killed my new lithium battery from all the ECU and dash config and starts. Swapped back to the OEM till I get a lithium charger.


Sent from my iPhone using Tapatalk

[Kurlon]

You can use a regular charger, just unplug it once it says the batt is charged to keep it from cooking the batt in float mode, no worries.

[xrocket21]

You can use a regular charger, just unplug it once it says the batt is charged to keep it from cooking the batt in float mode, no worries.

ehhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh

[Kurlon]

ehhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh

Ok, don't let it try to desulfate either, if it's one of THOSE chargers.

[Jim]

You can use a regular charger, just unplug it once it says the batt is charged to keep it from cooking the batt in float mode, no worries.

i have two lithium chargers in the trailer. i'll grab one next time i'm there. no issues using the OEM battery for now as that is plugged into a battery tender

[FriskyDingo]

300 swap header is 51mm OD.
LeoVince can is 53mm ID.

Weighing out options to have the header flared, clamp it, or get a can that fits better.


Sent from my iPhone using Tapatalk

2 mm, could ya just use a tail pipe expander?

[Jim]

2 mm, could ya just use a tail pipe expander?

Yes but then I’m stuck with a discontinued muffler if I need to replace it for whatever reason.

Rather get something that I knew fits and is still in the market.


Sent from my iPhone using Tapatalk

[Kurlon]

Pipe expander now, rent/borrow, get things mounted and running. Pocket the cost of the exhaust... then down the line, if the bad thing happens, spend the money then?

[Jim]

Pipe expander now, rent/borrow, get things mounted and running. Pocket the cost of the exhaust... then down the line, if the bad thing happens, spend the money then?

for the extra $150, i'll do things right the first time.

[RandyO]

for the extra $150, i'll do things right the first time.

what's right ? I say weld it on, if you want to replace, cut it off weld a different one on no worries about loose clamps, leaky joints

[Kurlon]

Ok, $150, go for it. I was thinking it'd be $500 or more.

[Jim]

what's right ? I say weld it on, if you want to replace, cut it off weld a different one on no worries about loose clamps, leaky joints

Absolutely not. I am not taking off that header again after the 4 evenings it took to get it to bolt up.


Sent from my iPhone using Tapatalk