woodcraft bar risers

[DankDirtyBird]

Hey everyone. I have a set of woodcraft clipons, but would love to trade someone for a 1 or 1.5 inch rise bracket. Mine have 0 rise and cause the levers to interfere with the plastics. Ill look up what size I have later, but they fit my 07 cbr 1000rr. Let me know if anyone would like to swap.

[The Snowman]

I just did the same thing last week. I managed to get everything so it didn't hit the plastics at either lock with the original 0 height clip-ons.

My issue was that the way the bike is designed and the aftermarket Penske suspension makes the bike higher in the back and I was constantly leaning on my hands. Not good for someone with carpal tunnel in both wrists.

I went with 1.5" of rise and I had to mess with the controls to get it so neither reservoir contacted the upper part of the upper by the windscreen. It also helps that I have a Puig racing screen, so it's higher than stock. I haven't taken it out yet, so I don't have an opinion.

If you want to maintain your current control positioning, I would go 1.0" and not 1.5".

[DankDirtyBird]

Chuck, much like you I have the same Penske setup. I'd at least want to go back to the stock height. I have to move the levers too high for normal riding comfort right now. Maybe it would be better to buy the 1 inch risers, and just ebay the ones that I have.

[DuncanMoto]

FYI - They are 50mm. clamps Dan. And here's a fitment chart link for anyone interested.

I have the 50mm. riser kits in stock when you're ready. ;-)
I also have black bars. ooooooh

We just finished our photo shoot for the new website. Enjoy the Woodcraft porn.
.

[The Snowman]

It's a huge difference (ote the bars are in the same position in both photos):

Standard clip-ons:


1.5" risers"

[butcher bergs]

Hey Chuck, did you notice you have a scratch on the front fairing? Between the headlights. I'd put a sticker over that or something if I were you.

[DuncanMoto]

Now i understand...

Sent from my PC36100 using Tapatalk

[DankDirtyBird]

FYI - They are 50mm. clamps Dan. And here's a fitment chart link for anyone interested.

I have the 50mm. riser kits in stock when you're ready. ;-)
I also have black bars. ooooooh

We just finished our photo shoot for the new website. Enjoy the Woodcraft porn.
.

I can't just bolt on one of those risers on the far right can I?

[The Snowman]

I can't just bolt on one of those risers on the far right can I?

I think you'd need to reposition both the brake and clutch reservoirs completely.

[DuncanMoto]

I can't just bolt on one of those risers on the far right can I?

No. Different clamps.

[The Snowman]

No. Different clamps.

Very true. YOu can use the same bars though.

PK had drilled mine to keep the throttle and left hand switch pod in place.

It was a 15 minute installation.

[DankDirtyBird]

Ok, well it looks like I need the new clamps. Anyone want to buy the standard clamps that I have????

[The Snowman]

Ok, well it looks like I need the new clamps. Anyone want to buy the standard clamps that I have????

Gotta be quicker. I just sold mine to Corey (hondarider102).

[DankDirtyBird]

Gotta be quicker. I just sold mine to Corey (hondarider102).

You SOB! Thats alright, there's gotta be someone else on here thats building a track bike and could use them.

[The Snowman]

You SOB! Thats alright, there's gotta be someone else on here thats building a track bike and could use them.

Yep. and the 50mm also fits the following bikes:

Aprilia
RS250

Ducati
620-1000 SS
Monster

Honda
RC51
CBR1000RR (04-07)

Kawasaki
ZX6/RR/636 (03+)
ZX10R (04+)

Suzuki
GSXR600 (94-96)
GSXR600 (04-05)
GSXR750 (93-95)
GSXR750 (96-05)
GSXR1000 (05-06)
GSXR1000 07-08
GSXR1000 09
GSXR1100
TL1000S/R
Hayabusa

Triumph
Daytona 675
Street Triple

Yamaha
R6 (05)
R6 06+
YZF750
R1 to 02